Видео

I have a similar build. Its yet to see a dyno. Im running a Lm7 from a 2002 avalanche with a built 4l60. 7835 vs racing turbo, with a walbro 750 fuel pump on 80 lb Deka injectors. I did a side dump out of the quarter panel and basically gutted the interior. Im currently running 12lbs boost on 18 degrees timing.

You saved the day, haven’t worked on one of these in over 20 years. I forgot about the in and out adjustments underneath…. Thank you!!!

this is the best video on the internet haha what a great race between these two!

You can see the GTO rear suspension bouncing. Needs to replace his coil springs. Those cars are notorious for spring failure. Factory springs were too weak.

I have a similar build. It's has a mild cam, lm7 with 7825 turbo. I'm still getting the bugs worked out. Im on the stock ecm still. Hopefully this week I'll have it ready to drive. Love the build.

Thanks for the video. I was searching how to so the window from wobbling and this video explains it towards the middle of it. Thanks again!!

Mustang left early and trans am was coming around when the mustang decided to brake.

dude you have no idea how helpful this was for my 4th gen firebird. It's very similar.

haha! e55 smoked as always! Easy!

Good video, I'm just going to my '92 T/A. Can you tell me or show me where the round donut glass stop is supposed to be?

Wow we literally have the same color bird thats crazy😅😊😂

Quick question where do u have you intercooler mounted? In front of the radiator i assume any problems with cooling ??

Monster clutch wants a .080-.100 of a clearance.

Whats the paint code? Wanna put it on my 89

That’s a lot of weight gone

Them aero dynamics a bitch with that window down

Im a build right now with a similar setup. 1991 z28 with lm7 btr cam, and vs racing turbo. Thats a clean build youve got. Make some more videos!

where did you buy your harness from. great vid!

Mustang driver jumping per usual

Bro was about to smoke that pony but he left off

thats amazing bro,great fab skill..add an irs and it would be over the top

thats one sexy bird

What’s the part number on the tree frog note pad?

What muffler are you using

Great video. Thank You. As a side note, I had trouble with my drivers widow even after adjusting. Turns out, the felt on the 2 window guides was completely worn away. I glued on new strips of felt, works great. Thanks again.

Gteat videos, i gotta replace mine in the spring. Went tight to the floor for engagement. Lol what clutch would you recommend for a 94 Z-28 with the Lt1 , 6 speed? Just haf put a Detroit locker with 373's and the clutch went south. Old cars = great fun!!

Hey that’s the Saleen I have now still a roller tho lol

@Transamman305 Do you still have this car?

That regal moves!! Forget the trans am

67 ' Camaro最高です！

So did you end up using a shim because I just got a McLeod clutch and I called them ahead time and they are telling me that I should not need a shim in my 2001 trans am

Both awsome cars

Camaro never had a 383 motor

You actually expect a gearbox to perform like a rack and pinion??

Is 5psi considered a boost anyway? I'm not hating. Just curious why so little.

Unsure if I measured mine properly, read 55mm on bearing , and 75mm from bellhousing to clutch fingers

Nice video. I'll have to adjust my side glass on my 94 TA..

Damn that camera man slowing everybody down🤦. 🔥🔥🔥 Video

Tho the mach1 is only a 4.6 small block v8, it's got 4valves per cylinder and are definitely no slouch even by today's standards. And with forged internals. Plus their very light. I've keepin up with a scatpack in my stock mach. Dude probably doesn't have a proper tune on his mach, and needs a driver mod lol.

Holy hell. I used to watch this video waaaay back in the day. At the time I had an 89 base firebird 305/auto and wanted so badly for mine to be as bad as I always thought this was. I kept up with your restoration project some years ago on the third gen forums. It’s nice to come across old inspiration again. I hope you’re well!

how do I adjust the lower stop from going down to far

Anyone notice the bike in the background racing with them 🤣

Hello, you should probably mention that all these adjustments are useless if the door hinge bushings are well worn.

I love you

Awesome!!!

Nope, just nope.. That aint possible. That wasn't an E55 or something was really wrong.

Awesome videos followed you for a while on TGO for a while. Not to take away from the suspension and how well it was done but what wheels are these?

Metric is sooooo much better, i can see you struggle to take in the unnecessary large numbers. Easier to read 35mm as apposed to 1.378.

Thanks for the video and info! Been looking all over for help with this adjustment for my car and man you saved me a lot of headache and time! Thanks man.

What happened to the rear wheel wells ? Looks like a California compliance thing 😞